Shibaura CM374 Operator's Manual

TRACTOR OPERATOR'S MANUALMODELCM314 CM374IHI GROUPIHI Shibaura Machinery Corporation

1-1PLEASE READ CAREFULLY:For a complete list of the pre-delivery servicechecks performed by your dealer, refer to thePRE-DELIVERY SERVICE

1-2GENERAL INFORMATIONMINIMUM HARDWARE TIGHTENING TORQUESIN FOOT POUNDS (NEWTON-METERS) FOR NORMAL ASSEMBLY APPLICATIONSMETRIC HARDWARE AND LOCKNUTSNO

1-3GENERAL INFORMATIONINTERNATIONAL SYMBOLSAs a guide to the operation of your tractor, various international symbols have been used on instrumentsand

2-1SEAT, SEAT BELT AND ROPSOPERATORS SEATYour seat is adjustable to obtain the mostcomfortable position.Seat Travel LeverBy tilting the Seat Travel Le

2-2STEERING WHEELADJUSTING THE STEERING WHEELThe CM mower is equipped with an adjustablesteering wheel which can telescope and tilt.To telescope t

DO NOT weld on ROPS, or use a damagedROPS. Replace ROPS if cracked or damaged.If the seat belt is to be cleaned, use soap andwater. Do n

2-4PROOF - METERThe Proof-Meter is located on the left side of theinstrument panel.Proof-Meter indicates hours of operation, andthe figures afte

SWITCHESKEY START SWITCHKEY START SWITCH1. ‘Off’ Position2. ‘On’ Position3. Heat Position4. Starter PositionTurning the key right to the “ON” position

2-6THROTTLE CONTROLPush the throttle forward to increase enginerpm. Pull the throttle rearward to decreaseengine rpm. Always operate mower deck o

DIFFERENTIAL CONTROLDIFFERENTIAL LOCK PEDALDepressing the pedal, locks the front axle shaftstogether, providing additional traction in wet orloo

0-1CONTENTSSAFETY ……………………………………………………………………………0-2SECTION1-GENERAL INFORMATION ………………………………………1-1SECTION2-OPERATION…………………………………………………………2-1SECTION3-L

CRUISE CONTROL SWITCH WARNING: TO AVOID INJURY, THE SWITCHSHOULD NOT BE PUT IN THE“ON” POSI-TION WHEN OPERATING AT TRANSPORTSPEED OR WHEN IN REV

AUTOMATIC OR PERMANENT FOURWHEEL DRIVE (FWD) SELECTOR LEVERFour Wheel Drive (FWD) Selector Lever A isactivated by the same lever as the one that

HYDRAULIC LIFT SYSTEM CONTROLSLIFT CONTROL LEVERThe front mounted equipment can be raisedand lowered by the lift control lever. Placehandle in the

BREAK-IN PROCEDURESYour CM Mower will provide long anddependable service if given proper care duringthe first 50-hour break-in period. Dur

STARTING THE ENGINESAFETY STARTING DEVICEYour CM Mower is equipped with four safetyswitches;HST foot pedals, PTO lever, master brake pedaland seat

2-13COLD WEATHER STARTINGIf the engine fails to start using the precedingwarm weather starting procedure or whenstarting the engine in cold we

2. Connect one end of the jumper cable to thebattery positive (+) terminal and the other tothe auxiliary battery positive (+) terminal.Conne

OPERATING THE HYDROSTATICTRANSMISSION AND PTOHYDROSTATIC TRANSMISSIONThe hydrostatic transmission is controlled by theHST foot pedals A, cruise c

AUTOMATIC OR PERMANENT FOUR-WHEEL DRIVE (FWD)The lever is used to select automatic Four-Wheel Drive or permanent Four-Wheel Drive.Four Wheel Drive (FW

OPERATING THE DIFFERENTIAL LOCKThe differential lock is engaged by depressingthe pedal A. Depressing the pedal locks bothdifferential gea

0-2SAFETY RULES1. SAFETY RULESPlease pay particular attention to all boxed-parts in the text which have the sign .This sign warns you to be careful

OPERATING THE HYDRAULIC LIFTSYSTEMThe hydraulic lift system provides accurate,smooth, and instant hydraulic power for raisingfront mounted e

The weight transfer valve should be usedaccording to the following procedures;1. With the engine running, push the hydrauliclift lever forward t

CM MOWER WEIGHTING (OPTIONAL)Rear end weights are recommended to increasestability, steering, traction on slopes or slipperysurfaces, and help p

OVERHEAT AND ENGINE OILPRESSURE ALARM BUZZERThe coolant temperature fluctuates dependingon ambient temperatures and working loads. Ifthe nee

WORKING LIGHTS (OPTIONAL)The work lights are available as a dealerinstalled accessory from your SHIBAURA dealer.CANOPY (2-post ROPS) (OPTIONAL)The can

Dual Pedal Turning Brakes Kit(OPTIONAL)The dual pedal turning brakes kit is available asa dealer installed Option from your SHIBAURAdealer.AUDIB

3-1SECTION 3LUBRICATION AND MAINTENANCEThis section gives full details of the service procedures necessary to maintain your CM Mower at peakefficiency

3-2LUBRICATION AND MAINTENANCENo.12320451,6789−710811121314151617LUBRICATION &MAINTENANCEITEMSEngine Oil LevelAir CleanerRadiator CoolantRadiator

3-3LUBRICATION AND MAINTENANCELUBRICATIONAdequate lubrication and maintenance on aregular schedule is vital to maintaining your CMmower. To ensure lo

3-4LUBRICATION AND MAINTENANCEFuel Usage Safety•UNDER NO CIRCUMSTANCES shouldgasoline, alcohol, or gasohol be added todiesel fuel. These combi

2) Thoroughly inspect the area where theequipment is to be used and remove allobjects which may be thrown by themachine (stones, sticks, meta

Refueling the TractorThe fuel tank filler cap A is located at the leftside of the tractor hood. Before removing thecap, wipe all dust

3-6SERVICE ACCESSOPENING HOODLoosen the Bolt B by tool, allowing to unlockthe hood latch A and raise the hood holdingthe hood handle.Clo

3-7ENGINEChecking the Engine Oil LevelNOTE: Check the engine oil level daily orafter every 10 hours of operation.1. After the engine has been stoppe

2. Next, place a container below the oil filter Ato catch the used oil and unscrew the oil filter.Discard the used oil and filter.3. Coat the gasket o

3-9Changing the Fuel Filter:NOTE: Change the diesel fuel filter after thefirst 50 hours of operation, then followingevery 200 operating hours the

AIR CLEANERThe air cleaner is accessed by opening thetractor hood.The air cleaner assembly contains twoelements: an outer primary element and an

3-11LUBRICATION AND MAINTENANCE3. After cleaning the element, check the innerdiameter seals for damage. If damage ispresent, replace the pri

3-12LIFTING SEATBy holding the grip of the tilting seat lockinglever on the lower part at the back of the seatand lifting it up, the loc

3-13LUBRICATION AND MAINTENANCE1. With the oil at normal operating temperature(Caution“Hot”oil!), drain and discard the oil byremoving the trans

HYDRAULIC OIL FILTER (SUCTION & HST)The hydraulic system is equipped with spin-ontype oil filters.NOTE: Replace the filters after the

- Before checking, cleaning or working onFront Mower;- After striking a foreign object. Inspect theFront Mower for damage and makerepairs before

3-15LUBRICATION AND MAINTENANCEREAR AXLE DIFFERENTIAL CASE ANDFINAL REDUCTION GEAR CASESChecking Oil Level: Check the oil level every100 hours.1.

3-16COOLING SYSTEMThe CM mower engine must operate at thecorrect temperature to obtain maximumefficiency and service life. This is dependent ont

Draining and flushing the Cooling systemNOTE: Drain and flush the radiator andengine block every 12 months. Refill with a50/50 mixture of per

3-18Fan BeltNOTE: Check the condition of the fan beltafter every 50 hours of operation. Check fanbelt tension after every 200 hours ofope

ALTERNATORThe CM mower 40-amp alternator is belt-drivenfrom the engine crankshaft pulley. It is importantthat belt slippage does not occur, or thechar

FUSE BLOCKThe fuse block, is located on the left side of themower compartment. Always replace blownfuses with the size specified for that circuit.FUSI

3-21LUBRICATION AND MAINTENANCEHEAD LAMPIf a head lamp fails to operate, the bulb must bereplaced. To change the bulb:1. Pull out the lower cover A

3-22BATTERYThe CM mower is equipped with a BCI group35, 12-bolt battery with a minimum coldcranking ability of 490 amps at-18°C (0°F)Make sure

MAINTENANCE AND INSPECTION OFTHE ROLLOVER PROTECTIVESTRUCTURE (ROPS)NOTE: Inspect the ROPS after the first 20hours of operation. Following the ini

3-24LUBRICATION AND MAINTENANCETIRESNOTE: Check tire pressure after every 50hours of operation or weekly.Tire inflation pressure affects the amount

You Front-tractor must be used with care.Therefore, decals have been placed on themachine, to remind you pictorially of mainprecautions to take during

WHEEL BOLT TORQUETighten the wheel bolts to the specified torqueanytime the wheel assembly is removed fromthe mower or the wheel bolts are

2. At the point of resistance (20% into thecontrol lever stroke), attach a pull scale to thePTO control lever. A reading of 5 kgf (11.5Lbs.) is

•Special diesel fuel system flushing oils areavailable from most oil companies. If specialflushing oil is not readily obtainable, mix 0.

4-1CM314 CM374ENGINEType ………………………………… Diesel DieselEngine Gross Horsepower ………… 22.4 kw (30HP) 26.8 kw ( 36HP)Cylinders …………………………… 33Bore …………………………

4-2SPECIFICATIONELECTRICAL SYSTEMAlternator …………………………… 12-volt, Heavy Duty,40 ampsBattery ……………………………… 12-volt, 53.9 amp hour rating w / negative gro

4-3SPECIFICATIONTRANSMISSION Type ………………………………… HST with 2 Range Gear Drive 4 WD Drive ………………………… Auto 4WD or Full 4WD Speed

4-4SPECIFICATIONWHEEL TREAD SETTNGS:FRONT:STD Tire Dished In ………………………… 990 mm 990 mm Dished Out………………………… 1050 mm 1050 mmREAR STD ………………………… 995 m

TEST DATASOUND MEASUREMENTSSound PowerCutting Attachment : CM-180PCM314 ・・・・・・・105dB(A) @2100 rpmCM374 ・・・・・・・105dB(A) @2100 rpmCutting Attachment :

4-6Wiring Diagram

4-7Air Cleaner ………………………………………3-10Alternator …………………………………………3-19Audible Backup Alram …………………………2-23Armrest……………………………………………2-1Battery ………………………………………

• Do not depress the brake pedal quickly.Quick brake will cause upset of the machine.• Do not open when hot.• Contents under pressure.• Always lock RO

4-8Steering Wheel …………………………………2-2Stopping the Engine ……………………………2-14Storing the Mower Unit …………………………3-25Symbols …………………………………………1-3Test Data …………………

4-9INOPERATIVE SERVICE CHECKS1. Tire pressure・・・・・・・・・・・・・・・・・・・・・・□2. Check air cleaner hose connection・・・・・・・・□3. Replace diesel fuel filter(s)・・・・・

4-11INOPERATIVE SERVICE CHECKS1. Tire pressure・・・・・・・・・・・・・・・・・・・・・・□2. Check air cleaner hose connection・・・・・・・・□3. Replace diesel fuel filter(s)・・・・

4-13

4-14

INSTRUCITON DECALSParking BrakeA Parking BrakeB “Lock” PositionC “Release” PositionKey SwitchA Engine “HEAT” PositionB Engine “STOP” or “OFF” Position

MACHINE IDENTIFICATION PLATEA CE Conformity MarkB Year of ManufactureC Weight in kgsD Name and Address of ManufacturerE Type of Front MowerF Serial Nu